> >>>>>Select SL77 Half Surface Geared Continuous Hinge
Reduced price! Select SL77 Half Surface Geared Continuous Hinge

Select Hinges

Previous Next

Select SL77 Half Surface Geared Continuous Hinge

SL77

$481.60

Details: Select SL77 Half Surface Geared Continuous Hinge

Frame leaf covers butt hinge preps. Tamper-resistant, removable door leaf cover. 3/32" door inset. For 1-3/4" doors. Long barrel nuts available for 2" to 2-1/4" doors. SL54 HD geared continuous hinges are BHMA Grade 1 certified.

Specifications

Material
Extruded 6063 T6 aluminum alloy with selflubricating polyester thrust bearings
Lengths
83", 85" and 95" lengths standard for nominal door heights. Custom lengths are available
Finishes
All SL77 hinges are stocked in Clear and Dark Bronze anodized aluminum. Custom anodized or painted finishes are available. Product painted or anodized in the field voids the SELECT hinge warranty
Closers
Conventional overhead surface, concealed sliding arm overhead or floor closers may be used with SELECT hinges. Pivot-type floor closers (with a fixed, conflicting center pivot) must be replaced

Load/Frequency Rating

Heavy Duty
Tested per BHMA standards. Up to 200 lb. doors (high-frequency) and up to 400 lb. doors (medium-frequency) without frame or door reinforcement; up to 600 lb. doors (low-frequency) with the use of Rivnuts in the frame

For 1-3/8" 1-3/4" doors standard; long barrel nuts available for 2" 2-1/4" doors. 48" max. door width in 16 gauge hollow metal (min.) or 1/8" aluminum (min.).

SL77 Hinge Screw Count

HINGE LENGTH & DUTY RATINGDOOR SCREWSFRAME SCREWS
83" HD1014
95" HD1115

Options

Header Gap Prep

No more shimming! Door leaf trimmed 1/8" at the top and bottom to incorporate clearance required for installation. No handing required; available on all models.

UL Labeled 3-HR. Fire Rating

For use on swinging single or pairs of fire doors, including double egress, up to 3 hours (not available on SL38) for hollow metal or steel covered composite and 1-1/2 hours for wood composite and wood core type fire doors with a maximum size of 4 ft. wide and 10 ft. high, installed in masonry or drywall.

Security Option

Non-removable bearing added at top of hinge to prevent material from falling into the opening between cap and gears. Hinge must be installed with security bearing at top of door. Handing required, except for SL11, SL27, SL38 and SL40. Not available with Hospital Tip.

Tamper-Resistant Hinge

Entire hinge prepared with set screws installed in every other bearing and tightened against inside of gear cap for additional security against tampering.

Hinge Preparation for TIPIT L

For SL21 and SL57 full surface hinges, and SL53, SL54 and SL77 half surface hinges. Factory preparation of door leaf covers, for field installation of TIPIT. Specify [TIPIT PREP] on your hinge order. Patented design.

Geared Hinge Fasteners

SDTF
12-24 3/4", Self-Drilling, Thread-Forming, 410 SS Screws, Phillips Undercut Flathead
TF
12-24 1/2", Thread-Forming, 410 SS Screws, Phillips Undercut Flathead (Pilot hole required)
WD
12-14 1-1/2", 410 SS Wood Screws
WD/SDTF
12-14 1-1/2", 410 SS Wood Screws and 12-24 3/4", Self-Drilling, Thread-Forming, 410 SS Screws
WD/TF
12-14 1-1/2", 410 SS Wood Screws and 12-24 -1/2", Thread-Forming, 410 SS Screws

Preparation & Accessories

Electrical

Electric Power Transfer Cutout

Features

  • 90-minute Fire Rating
  • 3-hour Fire Rating

Hospital Tip

TIPIT Ligature-Resistant Hospital Tip

Downloads

SELECT Hinge Performance

SELECT SL77 geared continuous hinges are listed and tested by Underwriters Laboratories to meet the Positive and Negative pressure requirements of UL10B and UL10C, and are in accordance with UBC 7.2 (1997). SELECT SL77 geared continuous hinges are for use on swinging single fire doors (max. door opening of 4'x10') or pairs of fire doors (max. door opening of 8'x10'), including double egress, installed in masonry or drywall. SELECT SL77 geared continuous hinges are rated for up to 1-1/2 hours for wood composite and wood core type fire doors. A special patented process can be added to increase the fire rating to 3 hours (NO FIRE PINS OR STUDS REQUIRED) for hollow metal or steel covered composite type doors.

Select Geared Continuous Hinge Comparison Table

All Select Geared Continous Hinges are made from Extruded 6063 T6 aluminum alloy with selflubricating polyester thrust bearings. All Heavy Duty Hinges are BHMA Grade 1 certified.

Model Type Standard Duty Heavy Duty Heavy Duty (LL) Sizes Load/Frequency
SL11Concealed✔✔✔83" - 120"For 1-3/4" doors. 48" Max. door width
SL14Concealed✔✔83" - 120"For 1-3/4" doors. 48" Max. door width
SL18Concealed✔✔✔83" - 120"For 1-3/4" doors. 48" Max. door width
SL24Concealed✔✔✔83" - 120"For 1-3/4" doors. 48" Max. door width
SL26Concealed✔83" - 120"For 2" to 2-1/4" doors. 48" Max. door width
SL27Concealed✔83" - 120"For 2" to 2-1/4" doors. 48" Max. door width
SL31Concealed✔83" & 95"For 1-3/4" doors. 48" Max. door width
SL38Concealed✔83" & 95"For 1" to 1-3/8" doors. 48" Max. door width
SL44Concealed✔83" & 95"For 1-3/4" doors. 48" Max. door width
SL48Concealed✔83" & 95"For 1-3/4" doors. 48" Max. door width
SL71Concealed✔83" & 95"For 1-3/4" doors. 48" Max. door width
SL84Concealed✔✔83" - 120"For 1-3/4" doors. 48" Max. door width
SL40Wide Throw✔83" & 95"For 1-3/4" doors. 48" Max. door width
SL41Swing Clear✔✔83" - 120"For 1-3/4" doors. 48" Max. door width
SL53Half Surface✔83" - 120"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL54Half Surface✔83" - 120"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL21Full Surface✔✔83" - 120"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL57Full Surface✔✔83" - 120"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL77Full Surface✔83" & 95"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL52Half Mortise✔83" - 120"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL60/SL62Toilet Partition57"For high-frequency partition doors 36" wide (Max.) weighing up to 80 pounds

Available Model Numbers and Combinations

Model/SKU Attributes
SL7783CLH Clear, 83"
SL7783BRH 83", Oxidized Satin Bronze
SL7795CLH Clear, 95"
SL7795BRH 95", Oxidized Satin Bronze