SL84 Concealed Geared Continous Hinge

SL84

$187.00

Details: SL84 Concealed Geared Continous Hinge

Narrow frame leaf allows for weatherstripping or smoke seal. Door edge protector. 1/16" door inset. For 1-3/4" doors. All SL84 geared continuous hinges are BHMA Grade 1 certified.

Specifications

Material
Extruded 6063 T6 aluminum alloy with self- lubricating polyester thrust bearings
Lengths
83", 85", 95" and 120" lengths standard for nominal door heights. Custom lengths are available
Finishes
All SL84 hinges are stocked in Clear and Dark Bronze anodized aluminum. Custom anodized or painted finishes are available. Product painted or anodized in the field voids the SELECT hinge warranty
Closers
Conventional overhead surface, concealed sliding arm overhead or floor closers may be used with SELECT hinges. Pivot-type floor closers (with a fixed, conflicting center pivot) must be replaced

Load/Frequency Ratings

Standard Duty
Tested per BHMA standards for medium-frequency doors up to 200 lb. without frame or door reinforcement
Heavy Duty
Tested per BHMA standards. Up to 200 lb. doors (high-frequency) and up to 400 lb. doors (medium-frequency) without frame or door reinforcement; up to 600 lb. doors (low-frequency) with the use of Rivnuts in the frame and door

For 1-3/4" doors. 48" max. door width in 16 gauge hollow metal (min.) or 1/8" aluminum (min.).

SL84 Hinge Screw Count

HINGE LENGTH & DUTY RATINGDOOR SCREWSFRAME SCREWS
83" HD1919
95" HD2121
83" LL2626
95" LL3030

Options

Header Gap Prep

No more shimming! Door leaf trimmed 1/8" at the top and bottom to incorporate clearance required for installation. No handing required; available on all models.

UL Labeled 3-HR. Fire Rating

For use on swinging single or pairs of fire doors, including double egress, up to 3 hours (not available on SL38) for hollow metal or steel covered composite and 1-1/2 hours for wood composite and wood core type fire doors with a maximum size of 4 ft. wide and 10 ft. high, installed in masonry or drywall.

Security Option

Non-removable bearing added at top of hinge to prevent material from falling into the opening between cap and gears. Hinge must be installed with security bearing at top of door. Handing required, except for SL11, SL27, SL38 and SL40. Not available with Hospital Tip.

Tamper-Resistant Hinge

Entire hinge prepared with set screws installed in every other bearing and tightened against inside of gear cap for additional security against tampering.

Hospital Tip

Angle-cut hinge preparation for new concealed hinges up to 95". Available on the following model hinges: SL11, SL14, SL18, SL24, SL26, SL27, SL31, SL38, SL44, SL48 and SL84 concealed hinges only. Handing required, except SL11, SL27 and SL38. Not available on hinges longer than 95". Not available on SL71 concealed safety hinges, SL21 and SL57 full surface hinges, SL53 and SL54 half surface hinges, SL40 wide throw hinges, SL41 swing clear hinges or SL60/62 toilet partition hinges.

Geared Hinge Fasteners

SDTF
12-24 3/4", Self-Drilling, Thread-Forming, 410 SS Screws, Phillips Undercut Flathead
TF
12-24 1/2", Thread-Forming, 410 SS Screws, Phillips Undercut Flathead (Pilot hole required)
WD
12-14 1-1/2", 410 SS Wood Screws
WD/SDTF
12-14 1-1/2", 410 SS Wood Screws and 12-24 3/4", Self-Drilling, Thread-Forming, 410 SS Screws
WD/TF
12-14 1-1/2", 410 SS Wood Screws and 12-24-1/2", Thread-Forming, 410 SS Screws

Preparation & Accessories

Features

  • 90-minute Fire Rating
  • 3-hour Fire Rating

Downloads

SELECT Hinge Performance

SELECT SL84 geared continuous hinges eliminate the gap between the door and frame, providing a weatherproof, rust-proof, tamper-proof barrier. When the door is closed, there are no accessible screws, bolts or pins.

SELECT SL84 geared continuous hinges are listed and tested by Underwriters Laboratories to meet the Positive and Negative pressure requirements of UL10B and UL10C, and are in accordance with UBC 7.2 (1997). SELECT SL84 geared continuous hinges are for use on swinging single fire doors (max. door opening of 4'x10') or pairs of fire doors (max. door opening of 8'x10'), including double egress, installed in masonry or drywall. SELECT SL84 geared continuous hinges are rated for up to 1-1/2 hours for wood composite and wood core type fire doors. A special patented process can be added to increase the fire rating to 3 hours (NO FIRE PINS OR STUDS REQUIRED) for hollow metal or steel covered composite type doors.

SELECT Advantages

Pair-Matched™ Hinge Leaves

Manufactured together, machined together and anodized together, making SELECT hinges fit your doors better and last longer. An exclusive SELECT benefit.

Select Geared Continuous Hinge Comparison Table

All Select Geared Continous Hinges are made from Extruded 6063 T6 aluminum alloy with selflubricating polyester thrust bearings. All Heavy Duty Hinges are BHMA Grade 1 certified.

Model Type Standard Duty Heavy Duty Heavy Duty (LL) Sizes Load/Frequency
SL11Concealed83" - 120"For 1-3/4" doors. 48" Max. door width
SL14Concealed83" - 120"For 1-3/4" doors. 48" Max. door width
SL18Concealed83" - 120"For 1-3/4" doors. 48" Max. door width
SL24Concealed83" - 120"For 1-3/4" doors. 48" Max. door width
SL26Concealed83" - 120"For 2" to 2-1/4" doors. 48" Max. door width
SL27Concealed83" - 120"For 2" to 2-1/4" doors. 48" Max. door width
SL31Concealed83" & 95"For 1-3/4" doors. 48" Max. door width
SL38Concealed83" & 95"For 1" to 1-3/8" doors. 48" Max. door width
SL44Concealed83" & 95"For 1-3/4" doors. 48" Max. door width
SL48Concealed83" & 95"For 1-3/4" doors. 48" Max. door width
SL71Concealed83" & 95"For 1-3/4" doors. 48" Max. door width
SL84Concealed83" - 120"For 1-3/4" doors. 48" Max. door width
SL40Wide Throw83" & 95"For 1-3/4" doors. 48" Max. door width
SL41Swing Clear83" - 120"For 1-3/4" doors. 48" Max. door width
SL53Half Surface83" - 120"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL54Half Surface83" - 120"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL21Full Surface83" - 120"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL57Full Surface83" - 120"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL77Full Surface83" & 95"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL52Half Mortise83" - 120"For 1-3/8" – 1-3/4" doors standard; 48" Max. door width
SL60/SL62Toilet Partition57"For high-frequency partition doors 36" wide (Max.) weighing up to 80 pounds

Available Model Numbers and Combinations

Model/SKU Attributes
SL8483CLL Clear, 83", Heavy Duty ( LL )
SL8483BRL 83", Oxidized Satin Bronze, Heavy Duty ( LL )
SL8485CLL Clear, 85", Heavy Duty (LL)
SL8485BRL Oxidized Satin Bronze, 85", Heavy Duty (LL)
SL8495CLL Clear, 95", Heavy Duty (LL)
SL8495BRL 95", Oxidized Satin Bronze, Heavy Duty (LL)
SL8412CLL Clear, Heavy Duty (LL), 120"
SL8412BRL Oxidized Satin Bronze, Heavy Duty (LL), 120"
SL8483CLH Clear, 83", Heavy Duty
SL8483BRH 83", Oxidized Satin Bronze, Heavy Duty
SL8485CLH Clear, Heavy Duty, 85"
SL8485BRH Oxidized Satin Bronze, Heavy Duty, 85"
SL8495CLH Clear, 95", Heavy Duty
SL8495BRH 95", Oxidized Satin Bronze, Heavy Duty
SL8412CLH Clear, Heavy Duty, 120"

View All Model Numbers and Options