For 2" to 2-1/4" doors, up to 1,000 lb. Frame leaf covers butt hinge preps. Staggered hole pattern. Flush mounted (no door inset). SL27 LL geared continuous hinges are BHMA Grade 1 certified.
Specifications
- Material
- Extruded 6063 T6 aluminum alloy with self- lubricating polyester thrust bearings
- Lengths
- 83", 85", 95" and 120" lengths standard for nominal door heights. Custom lengths are available
- Finishes
- All SL27 hinges are stocked in Clear and Dark Bronze anodized aluminum. Custom anodized or painted finishes are available. Product painted or anodized in the field voids the SELECT hinge warranty
- Closers
- Conventional overhead surface, concealed sliding arm overhead or floor closers may be used with SELECT hinges. Pivot-type floor closers (with a fixed, conflicting center pivot) must be replaced
Load/Frequency Rating
- Heavy Duty (LL)
- For low-frequency doors up to 1,000 lb., including most lead-lined doors. Rivnuts are recommended in the frame and door on extremely tall, extremely heavy or wide doors
For 2" to 2-1/4" doors. 48" max. door width in 16 gauge hollow metal (min.) or 1/8" aluminum (min.).
SL27 Hinge Screw Count
HINGE LENGTH & DUTY RATING | DOOR SCREWS | FRAME SCREWS |
83" LL | 25 | 25 |
85" LL | 25 | 25 |
95" LL | 29 | 29 |
120" LL | 33 | 33 |
Options
Header Gap Prep
No more shimming! Door leaf trimmed 1/8" at the
top and bottom to incorporate clearance required
for installation. No handing required; available on
all models.
UL Labeled 3-HR. Fire Rating
For
use on swinging single or pairs of fire doors, including double
egress, up to 3 hours (not available on SL38) for hollow
metal or steel covered composite and 1-1/2 hours for wood
composite and wood core type fire doors with a maximum size
of 4 ft. wide and 10 ft. high, installed in masonry or drywall.
Security Option
Non-removable bearing added at top of hinge to prevent
material from falling into the opening between cap and
gears. Hinge must be installed with security bearing at top
of door. Handing required, except for SL11, SL27, SL38 and
SL40. Not available with Hospital Tip.
Tamper-Resistant Hinge
Entire hinge prepared with set screws installed in every
other bearing and tightened against inside of gear cap for
additional security against tampering.
Hospital Tip
Angle-cut hinge preparation for new concealed hinges
up to 95". Available on the following model hinges: SL11,
SL14, SL18, SL24, SL26, SL27, SL31, SL38, SL44 and
SL48 concealed hinges only. Handing required, except
SL11, SL27 and SL38. Not available on hinges longer than
95". Not available on SL71 concealed safety hinges, SL21
and SL57 full surface hinges, SL53 and SL54 half surface
hinges, SL40 wide throw hinges, SL41 swing clear hinges or
SL60/62 toilet partition hinges.
Geared Hinge Fasteners
- SDTF
- 12-24 × 3/4", Self-Drilling, Thread-Forming, 410 SS Screws, Phillips Undercut Flathead
- TF
- 12-24 × 1/2", Thread-Forming, 410 SS Screws, Phillips Undercut Flathead (Pilot hole required)
- WD
- 12-14 × 1-1/2", 410 SS Wood Screws
- WD/SDTF
- 12-14 × 1-1/2", 410 SS Wood Screws and 12-24 × 3/4", Self-Drilling, Thread-Forming, 410 SS Screws
- WD/TF
- 12-14 × 1-1/2", 410 SS Wood Screws and 12-24 ×-1/2", Thread-Forming, 410 SS Screws
Preparation & Accessories
Features
- 90-minute Fire Rating
- 3-hour Fire Rating
Downloads
SELECT Hinge Performance
SELECT SL27 geared continuous hinges
are listed and tested by Underwriters
Laboratories to meet the Positive and
Negative pressure requirements of UL10B
and UL10C, and are in accordance with UBC
7.2 (1997). SELECT SL27 geared continuous
hinges are for use on swinging single fire
doors (max. door opening of 4'x10') or pairs
of fire doors (max. door opening of 8'x10'),
including double egress, installed in masonry
or drywall. SELECT SL27 geared continuous
hinges are rated for up to 1-1/2 hours for
wood composite and wood core type fire
doors. A special patented process can be
added to increase the fire rating to 3 hours
(NO FIRE PINS OR STUDS REQUIRED) for
hollow metal or steel covered composite type
doors.
SELECT Advantages
Pair-Matched™ Hinge Leaves
Manufactured together, machined together
and anodized together, making SELECT
hinges fit your doors better and last longer.
An exclusive SELECT benefit.
Lifetime Lubrication
Eliminates the need for periodic maintenance.
Quiet performance. Fights gear cap wear.
An exclusive SELECT benefit.
Anodized After Machining
Delivers superior wear, durability and
life. Inhibits corrosion. Few hinge makers
follow SELECT’s lead in using this superior
manufacturing process.
Meets Leed Requirements
Made from recycled aluminum.
Reduces environmental impact
and qualifies for LEED points.
An exclusive SELECT benefit.
Patented 3-Hr. Fire Rating
Most SELECT hinges are fire rated for
90 minutes. 3-Hr. fire rating, optional at
extra cost, approved for positive/negative
pressure. No fire pins or studs required.
Patented design innovation. An exclusive
SELECT benefit.
Consistent Templating
Hole pattern is identical on both Standard
and Heavy Duty models, so SELECT hinges
line up precisely for easier and faster
installation. An exclusive SELECT benefit.
Coated Fasteners
Provide additional corrosion protection with
either self-drilling, thread-forming (SDTF) or
thread-forming (TF) screws.
An exclusive SELECT benefit.
Custom Colors
Match any paint color on the gear cap or
the entire hinge and fasteners, including
our always-in-stock Bone White gear caps.
Anodized colors also available.