Door edge protector. Requires 2-1/4" frame face for full rotation clearance. 1-1/2" frame face needed for mounting. 1/16" door inset. For 1-3/4" doors. All SL41 geared continuous hinges are BHMA Grade 1 certified.
Specifications
- Material
- Extruded 6063 T6 aluminum alloy with selflubricating polyester thrust bearings
- Lengths
- 83", 85", 95" and 120" lengths standard for nominal door heights. Custom lengths are available
- Finishes
- All SL41 hinges are stocked in Clear and Dark Bronze anodized aluminum. Custom anodized or painted finishes are available. Product painted or anodized in the field voids the SELECT hinge warranty
- Closers
- Conventional overhead surface, concealed sliding arm overhead or floor closers may be used with SELECT hinges. Pivot-type floor closers (with a fixed, conflicting center pivot) must be replaced
Load/Frequency Ratings
- Heavy Duty
- Tested per BHMA standards. Up to 200 lb. doors (high-frequency) and up to 400 lb. doors (medium-frequency) without frame or door reinforcement; up to 600 lb. doors (low-frequency) with the use of Rivnuts in the frame and door
- Heavy Duty (LL)
- Our HD hinge with additional fastener holes for low-frequency doors up to 1,000 lb., including most lead-lined doors. Rivnuts are recommended in the frame and door on extremely tall, extremely heavy or wide doors
For 1-3/4" doors. 48" max. door width in 16 gauge hollow metal (min.) or 1/8" aluminum (min.).
SL41 Hinge Screw Count
HINGE LENGTH & DUTY RATING | DOOR SCREWS | FRAME SCREWS |
83" HD | 19 | 25 |
85" HD | 19 | 25 |
95" HD | 21 | 27 |
120" HD | 23 | 29 |
83" LL | 26 | 32 |
85" LL | 26 | 32 |
95" LL | 30 | 36 |
120" LL | 34 | 40 |
Options
Header Gap Prep
No more shimming! Door leaf trimmed 1/8" at the
top and bottom to incorporate clearance required
for installation. No handing required; available on
all models.
UL Labeled 3-HR. Fire Rating
For
use on swinging single or pairs of fire doors, including double
egress, up to 3 hours (not available on SL38) for hollow
metal or steel covered composite and 1-1/2 hours for wood
composite and wood core type fire doors with a maximum size
of 4 ft. wide and 10 ft. high, installed in masonry or drywall.
Security Option
Non-removable bearing added at top of hinge to prevent
material from falling into the opening between cap and
gears. Hinge must be installed with security bearing at top
of door. Handing required, except for SL11, SL27, SL38 and
SL40. Not available with Hospital Tip.
Tamper-Resistant Hinge
Entire hinge prepared with set screws installed in every
other bearing and tightened against inside of gear cap for
additional security against tampering.
Geared Hinge Fasteners
- SDTF
- 12-24 × 3/4", Self-Drilling, Thread-Forming, 410 SS Screws, Phillips Undercut Flathead
- TF
- 12-24 × 1/2", Thread-Forming, 410 SS Screws, Phillips Undercut Flathead (Pilot hole required)
- WD
- 12-14 × 1-1/2", 410 SS Wood Screws
- WD/SDTF
- 12-14 × 1-1/2", 410 SS Wood Screws and 12-24 × 3/4", Self-Drilling, Thread-Forming, 410 SS Screws
- WD/TF
- 12-14 × 1-1/2", 410 SS Wood Screws and 12-24 ×-1/2", Thread-Forming, 410 SS Screws
Preparation & Accessories
Features
- 90-minute Fire Rating
- 3-hour Fire Rating
Downloads
SELECT Hinge Performance
SELECT SL41 geared continuous hinges are listed and tested by Underwriters Laboratories to meet the Positive and Negative pressure requirements of UL10B and UL10C, and are in accordance with UBC 7.2 (1997). SELECT SL41 geared continuous hinges are for use on swinging single fire doors (max. door opening of 4'x10') or pairs of fire doors (max. door opening of 8'x10'), including double egress, installed in masonry or drywall. SELECT SL41 geared continuous hinges are rated for up to 1-1/2 hours for wood composite and wood core type fire doors. A special patented process can be
added to increase the fire rating to 3 hours (NO FIRE PINS OR STUDS REQUIRED) for hollow metal or steel covered composite type doors.
SELECT Advantages
Pair-Matched™ Hinge Leaves
Manufactured together, machined together
and anodized together, making SELECT
hinges fit your doors better and last longer.
An exclusive SELECT benefit.
Lifetime Lubrication
Eliminates the need for periodic maintenance.
Quiet performance. Fights gear cap wear.
An exclusive SELECT benefit.
Anodized After Machining
Delivers superior wear, durability and
life. Inhibits corrosion. Few hinge makers
follow SELECT’s lead in using this superior
manufacturing process.
Meets Leed Requirements
Made from recycled aluminum.
Reduces environmental impact
and qualifies for LEED points.
An exclusive SELECT benefit.
Patented 3-Hr. Fire Rating
Most SELECT hinges are fire rated for
90 minutes. 3-Hr. fire rating, optional at
extra cost, approved for positive/negative
pressure. No fire pins or studs required.
Patented design innovation. An exclusive
SELECT benefit.
Consistent Templating
Hole pattern is identical on both Standard
and Heavy Duty models, so SELECT hinges
line up precisely for easier and faster
installation. An exclusive SELECT benefit.
Coated Fasteners
Provide additional corrosion protection with
either self-drilling, thread-forming (SDTF) or
thread-forming (TF) screws.
An exclusive SELECT benefit.
Custom Colors
Match any paint color on the gear cap or
the entire hinge and fasteners, including
our always-in-stock Bone White gear caps.
Anodized colors also available.